Omen Def Mk.I-B FRD Upgrade Kit

grid-omen-def-01.jpg
grid-omen-def-01.jpg

Omen Def Mk.I-B FRD Upgrade Kit

1,199.00

$400 refund with the safe return of the old drivers. This service is only available direct from Zu. Those living outside the U.S. will simply email info@zuaudio.com to coordinate shipping.

Update your original Omen Def loudspeakers to full Mk.I-B status with this simple full-range driver and tweeter assembly (sold separately) swap out.

Omen Def Mk.I-B is now fitted with our high-output nanotech driver and marked as one-bee [Mk.I-B] and we are making the drivers available to those that would like to upgrade their original Omen Def loudspeakers.

(Kit Price is for a matched 2-channel set of parts.)

Get your tools here.

 

Quantity:
Add To Cart

[OMEN DEF 1-B UPGRADE KIT DETAILS]

The most important element of a loudspeaker is the driver—the round part that vibrates and turns electric power into sound. And when a loudspeaker is built around a full-range driver like ours it makes the driver all that much more critical. Omen Def Mk.I-B has one very big difference over it’s predecessor, it features the Dominance developed nanotech high-output driver. There are no other changes but the difference is pretty huge—more resolution of bass, mids and treble, more resolution of tone and texture, and better dynamic handling of complex music.

Omen Def Mk.I-B Can Be Identified By Two Main Features:

  • The revision Mk.I-B nameplate on the back of the speaker.
  • The engraved model number in the full-range driver.

What’s In The Kit?

2x Matched pair (4x total units) of Zu103ND/G1-16 drivers (high-output paper-cored nanotech 10” full-range drivers factory burned-in for 600 peddle to the metal hours).

1x Purpose built packaging—to ensure the safe return of your old drivers you must repackage the old ones the same way the new ones were packaged. If they’re not, and damage results you will not receive a refund.

Other Options Not Included In The Base Kit

New high-pass network (ClarityCap MR based).Clarity high-pass requires the swapping of your current tweeters.

Required Tools

  • Clean workspace; a blanket over coffee table is perfect.
  • T-25 screwdriver (not included).

How It’s Done 

This is a very easy swap, and no soldering is required.

  • Make sure you are button, snaps, belt buckle and wristwatch free.
  • Switch off your electronics and disconnect your speaker cables.
  • With a clean work space and a clean blanket or rug, lay it down with drivers facing up.
  1. Careful not to poke a hole in the cone or surround, remove the full-range driver fasteners.
  2. Remove the full-range machined trim ring and sit it aside.
  3. Grab hold of the machined center cylinder of the driver and lift it up, or use the rim.
  4. With it just clear of the cabinet cradle the driver from the backside with your other hand.
  5. Remove leads by gently rocking the connector longitudinally and pulling.
  6. After all leads are disconnected from the full-range driver set it off to the side.
  7. Now move the new FRD into position, connect red to (+), black to (–) then fit the FRD.

Torque The Full-Range Driver

First pass around, gently torque the screws.
Second pass around, torque firmly; using standard screwdriver and one hand.
Third pass around, torque as tightly as you can; using standard screwdriver and one hand (80 inch pounds [9 N-m]).

Repackage Old Drivers

Repack the old drivers exactly like you received them. Use the hard gasket between the two drivers. Use the same fasteners. Torque the screw with a 3/16” hex screwdriver or a T-25 screwdriver. Send them back for refund.